Dishwasher Fixed
Gasket failure in Burnaby. Installed redesigned Electrolux bottom door seal. Moisture containment test passed.
- 10+ Years Experience in Burnaby
- Fully Insured
- 7 days, 6:30 AM–9:30 PM
Electrolux Dishwasher Repair in Burnaby
Need Electrolux dishwasher repair in Burnaby? $149.95 diagnostic applied to your repair, 7 days a week, 6:30 AM–9:30 PM. Call 604-510-0707.
Serving homeowners in and around Burnaby: Top rated Appliance Repair Service in Burnaby. Our appliance service technicians have provided honest, accurate diagnostics in Burnaby for over 10 years. Specializing in fixing Fridges, Washers, Dryers, Ovens, and Dishwashers.
$149.95 Diagnostic / Estimation Price: Applied directly to the cost of your repair.
Your local appliance technician in Burnaby
From Metrotown to North Burnaby, our service fleet is equipped to handle dishwasher failures across the city with OEM parts.
Broken Glass & Pump Jams
"Grinding noises in Burnaby dishwashers usually indicate debris in the macerator. We dismantle the sump to protect the wash motor from permanent damage."
What's Actually Wrong With It?
Electrolux Dishwasher problems I see in Burnaby — and how I fix them
Select your dishwasher issue below, and I'll tell you what I usually see when I open these up in Burnaby.
Electrolux Dishwasher standing water — what usually causes it?
A piece of hard debris got past the filter and jammed the drain pump blades. I extract the water, pull the pump off the sump, remove the jam, and test it with 120V to ensure it still pumps.
Failed Component: Drain Pump
Electrolux Dishwasher dishes dirty — what usually causes it?
The plastic wash impeller sheared off the motor shaft, resulting in zero water pressure. I clean the spray arms first. If pressure is still dead, I have to install a new main circulation pump.
Failed Component: Wash Motor
Electrolux Dishwasher leaking floor — what usually causes it?
A degraded bottom door sweep, or a split spray arm shooting water directly at the door. I check the wash arm for cracks. If it's fine, I press a new watertight OEM rubber gasket around the tub.
Failed Component: Door Seal / Arm
Electrolux Dishwasher blinking lights — what usually causes it?
A blown thermal fuse in the top console severed power to the logic board. I trace the line voltage to the door. I replace the blown bi-metal fuse and the wire harness to restore power.
Failed Component: Control Board
Electrolux Dishwasher dishes wet — what usually causes it?
The 120V heating coil at the bottom of the tub blistered and burned out. I measure resistance across the two element nuts under the tub. If it's open, I swap in a new heating element.
Failed Component: Heating Element
Electrolux Dishwasher grinding noise — what usually causes it?
A piece of bone or glass is caught in the macerator blade inside the pump. I dismantle the sump assembly from the inside, extract the glass, and check the chopper screen for damage.
Failed Component: Chopper Blade
Electrolux Dishwasher won't fill — what usually causes it?
The brass water valve is calcified, or the safety float switch is stuck in the "up" position. I make sure the float drops. Then I ohm-test the valve. If it's dead, I swap the housing to get water flowing.
Failed Component: Inlet Valve
Electrolux Dishwasher soap dispenser — what usually causes it?
The tiny actuator that pops the soap door open during the cycle burned out. I test if the board is sending 120V to the door. If it is, but the door stays shut, I replace the whole dispenser module.
Failed Component: Wax Motor
Electrolux Dishwasher door won't latch — what usually causes it?
The microswitch in the latch broke, so the machine thinks the door is open. I realign the tub in the cabinets and replace the plastic latch block at the top of the door.
Failed Component: Interlock Switch
Electrolux Dishwasher swampy odor — what usually causes it?
Sink water is backflowing into the dishwasher because the drain hose isn't looped high enough. I fix the plumbing loop under the sink, extract the old food from the filter, and run a high-heat sanitization.
Failed Component: Drain Hose / Sump
⚠️ Disclaimer: This is not DIY advice. Modern appliances utilize lethal high-voltage circuits. Diagnostics and repairs should only be performed by a Trained and Certified Appliance Service Technician.
$149.95 diagnostic, applied to your repair. Open 7 days, 6:30 AM–9:30 PM.
Common Electrolux Dishwasher error codes
| Code | What it means |
|---|---|
i20 | Drain Blockage / Pressure Switch |
i30 | Leak Detected in Base Pan |
i40 | Pressure Sensor Fault |
I Know These Brands Inside and Out
After many years, you learn the quirks of every manufacturer. I stock the truck based on what breaks the most.
Frigidaire & Electrolux
If your Frigidaire fridge starts beeping with a "SY EF" code, the freezer fan died. For their front-load washers, if the door won't unlock, the latch wax motor burned out. I bypass the lock, get your laundry out, and swap the latch assembly.
Should I Fix It Or Toss It?
My honest advice on the lifespan of your Dishwasher. Expand below.
Dishwashers
✓ Fix It: Drain blockages, bad water inlet valves, or broken door latches. Very common and worth fixing.
✕ Replace It: If the plastic or stainless steel inner tub has physically cracked and is leaking water straight through the chassis. You can't patch that.
Typical repairs we handle in Burnaby
Representative examples of what we find once the machine is open.
Dishwasher Fixed
Sump assembly in Burnaby cleared of foreign debris. Electrolux wash motor torque tested and confirmed operational.
Dishwasher Fixed
Hydraulic drainage failure in Burnaby. Cleared external line obstruction. Electrolux drain pump amp-draw within normal range.