Washer Fixed
Arrived in Villeray. The Kenmore washer was shaking violently on spin cycle. The hydraulic suspension rods had lost all their dampening fluid. Replaced the set of 4 rods.
- 50+ Years Experience in Villeray
- Fully Insured
- 7 days, 6:30 AM–9:30 PM
Kenmore Washer Repair in Villeray
Need Kenmore washer repair in Villeray? $149.95 diagnostic applied to your repair, 7 days a week, 6:30 AM–9:30 PM. Call 514-700-0706.
Serving homeowners in and around Villeray: Hi, I'm Bob. I've been opening up washing machines and diagnosing fridges across Villeray for 50 years. I test it, find the exact broken part, and give you a straight path to fixing it.
$149.95 Diagnostic / Estimation Price: Applied directly to the cost of your repair.
Your local appliance technician in Villeray
“Cruising through the neighborhoods to fix a washer reminds me why I've done this for 50 years. From the busy main roads to your quiet driveway, I bring a fully stocked truck so you don't have to wait days for parts. I isolate the exact fault and fix it right the first time.”— Bob, Master Technician
Heavy Loads & Drain Clogs
"Most service calls in Villeray for washers full of water aren't dead motors; they are pump blockages. We clear the impeller and test the drain cycle immediately."
What's Actually Wrong With It?
Kenmore Washer problems I see in Villeray — and how I fix them
Select your washer issue below, and I'll tell you what I usually see when I open these up in Villeray.
Kenmore Washer won't drain — what usually causes it?
Coins or bobby pins jammed the drain pump impeller. I open the lower panel, physically clear the clog from the trap, and test the motor to make sure it didn't burn out.
Failed Component: Drain Pump
Kenmore Washer clothes wet — what usually causes it?
A bad Hall sensor (Rotor Position) or a snapped drive belt is preventing high RPMs. I test the speed sensor communication. If it's dead, the board aborts the spin. I replace the sensor or belt.
Failed Component: Spin Cycle
Kenmore Washer leaking door — what usually causes it?
A rip in the massive rubber gasket, usually from catching a zipper in the door. I pull the front chassis off, remove the tension springs, and seat a brand-new factory rubber bellows.
Failed Component: Door Bellows
Kenmore Washer shaking violently — what usually causes it?
The hydraulic shock absorbers or suspension rods have lost their dampening fluid. I press down on the tub. If it bounces like a basketball, the shocks are shot. I replace the full set of four.
Failed Component: Suspension System
Kenmore Washer won't agitate — what usually causes it?
Shattered motor coupling or stripped nylon agitator dogs. I tip the machine back and check the linkage. It's usually a quick fix replacing the plastic drive components.
Failed Component: Transmission / Coupling
Kenmore Washer fills slowly — what usually causes it?
Hard water calcium has completely blocked the mesh screens, or the solenoids are weak. I check the hoses first. If they are clear, I ohm-test the 120V water valve and replace it if the coils are failing.
Failed Component: Inlet Valve
Kenmore Washer completely dead — what usually causes it?
A broken door switch interlock. The machine won't start if it thinks the door is open. I trace the power from the wall plug to the board. Usually, I just need to swap the broken door latch assembly.
Failed Component: Power Supply
Kenmore Washer stops mid cycle — what usually causes it?
The water level sensor is getting bad data from a clogged air dome tube. I blow out the pressure hose. If the sensor is still reading wrong, I replace the analog switch on the console.
Failed Component: Pressure Switch
Kenmore Washer door stuck — what usually causes it?
The wax motor in the lock burned out, or there's still water in the tub. I use the manual bypass to get your laundry out, then diagnose whether the pump or the lock itself failed.
Failed Component: Door Latch Solenoid
Kenmore Washer mold smell — what usually causes it?
Soap scum and bacteria buildup behind the drum from using too much cold water. I run a deep chemical descaling and physically clean the door boot where the bio-film hides.
Failed Component: Outer Tub Bearing
⚠️ Disclaimer: This is not DIY advice. Modern appliances utilize lethal high-voltage circuits. Diagnostics and repairs should only be performed by a Trained and Certified Appliance Service Technician.
$149.95 diagnostic, applied to your repair. Open 7 days, 6:30 AM–9:30 PM.
I Know These Brands Inside and Out
After many years, you learn the quirks of every manufacturer. I stock the truck based on what breaks the most.
Kenmore
Kenmore didn't build their own machines; they were made by Whirlpool, LG, and Frigidaire. I cross-reference the 3-digit prefix on your model number (like 110 or 795) to find out exactly who built it, so I can source the right original factory part.
Should I Fix It Or Toss It?
My honest advice on the lifespan of your Washer. Expand below.
Washers & Dryers
✓ Fix It: Clogged drain pumps, snapped dryer belts, burnt thermal fuses, or bad door latches. These are simple, fast, same-day fixes.
✕ Replace It: If a front-load washer sounds like a jet engine on spin cycle and it's over 8 years old, the rear tub bearing is shattered.
Typical repairs we handle in Villeray
Representative examples of what we find once the machine is open.
Washer Fixed
Customer in Villeray said their Kenmore washer door wouldn't unlock. Found a burnt-out wax motor in the latch assembly. Bypassed the lock to get their laundry out, installed new latch.
Washer Fixed
Got a call for a leaking Kenmore washer in Villeray. Found a tear in the rubber door boot from an overloaded spin cycle. Pulled the front panel, put a new OEM gasket on. No more leaks.