Dryer Fixed
Arrived in Vieux-Longueuil. Client said the Kenmore dryer was spinning but dead cold. Tested the circuits and found a blown thermal safety fuse. Swapped it out and cleaned the wall vent.
- 50+ Years Experience in Vieux-Longueuil
- Fully Insured
- 7 days, 6:30 AM–9:30 PM
Kenmore Dryer Repair in Vieux-Longueuil
Need Kenmore dryer repair in Vieux-Longueuil? $149.95 diagnostic applied to your repair, 7 days a week, 6:30 AM–9:30 PM. Call 514-700-0706.
Serving homeowners in and around Vieux-Longueuil: Hi, I'm Bob. I've been opening up washing machines and diagnosing fridges across Vieux-Longueuil for 50 years. I test it, find the exact broken part, and give you a straight path to fixing it.
$149.95 Diagnostic / Estimation Price: Applied directly to the cost of your repair.
Your local appliance technician in Vieux-Longueuil
“Cruising through the neighborhoods to fix a dryer reminds me why I've done this for 50 years. From the busy main roads to your quiet driveway, I bring a fully stocked truck so you don't have to wait days for parts. I isolate the exact fault and fix it right the first time.”— Bob, Master Technician
Overheating & Clogged Vents
"Dryers in Vieux-Longueuil that spin but don't heat often have a tripped thermal safety. This is almost always caused by restricted airflow in the wall duct."
What's Actually Wrong With It?
Kenmore Dryer problems I see in Vieux-Longueuil — and how I fix them
Select your dryer issue below, and I'll tell you what I usually see when I open these up in Vieux-Longueuil.
Kenmore Dryer no heat — what usually causes it?
A safety fuse blew because your wall vent is choked with lint. I test the heater coil. I'll replace the blown fuse, but I will also test your exhaust airflow to make sure it doesn't blow again.
Failed Component: Heating Element / Fuse
Kenmore Dryer loud squeaking — what usually causes it?
The drum support rollers have flattened out, causing metal-on-metal friction. I do a total mechanical teardown. I swap the rollers, idler pulley, and belt all at once so it runs like new.
Failed Component: Rotational Matrix
Kenmore Dryer takes too long — what usually causes it?
Massive lint blockage inside the blower wheel housing or wall duct. I measure the CFM airflow. I'll physically extract the lint blocks inside the machine and test the element cycling.
Failed Component: Airflow Exhaust
Kenmore Dryer motor hums won't turn — what usually causes it?
The heavy-duty belt that turns the drum finally snapped. I open the top, thread a new multi-ribbed OEM belt around the drum, and lock it into the motor tensioner.
Failed Component: Drive Belt
Kenmore Dryer won't start — what usually causes it?
A blown main thermal fuse, or a broken door switch plunger. I check the door switch with a meter. If it's fine, I trace the motor circuit to find the blown safety fuse.
Failed Component: Thermal Fuse / Switch
Kenmore Dryer overheating — what usually causes it?
The thermostat fused shut, or the heating element grounded itself to the metal casing. I check if the element stays on when the machine is off. If so, it's grounded and I replace the entire heater box immediately.
Failed Component: Cycling Thermostat
Kenmore Dryer stops abruptly — what usually causes it?
The motor bearings are failing, causing it to overheat and trip the internal thermal switch. If it starts again after cooling down for 30 minutes, the motor is dying. I swap the complete 120V drive motor.
Failed Component: Drive Motor
Kenmore Dryer burning smell — what usually causes it?
Lint has bypassed the trap and is sitting directly on the 240V heating coils. This is a fire hazard. I pull the heater box, clear all scorched debris, and check the wall plug for melted wires.
Failed Component: Lint Combustion
Kenmore Dryer door pops open — what usually causes it?
The tiny plastic door strike has worn down from years of tumbling clothes hitting it. I pry out the old clips and snap in new, high-tension OEM catches so the door stays firmly shut.
Failed Component: Door Catch
Kenmore Dryer noisy thumping — what usually causes it?
The felt or Teflon pads holding up the front of the drum have worn completely away. I lift the drum out and rivet or glue new glide pads onto the front bulkhead to stop the scraping.
Failed Component: Drum Glides
⚠️ Disclaimer: This is not DIY advice. Modern appliances utilize lethal high-voltage circuits. Diagnostics and repairs should only be performed by a Trained and Certified Appliance Service Technician.
$149.95 diagnostic, applied to your repair. Open 7 days, 6:30 AM–9:30 PM.
I Know These Brands Inside and Out
After many years, you learn the quirks of every manufacturer. I stock the truck based on what breaks the most.
Kenmore
Kenmore didn't build their own machines; they were made by Whirlpool, LG, and Frigidaire. I cross-reference the 3-digit prefix on your model number (like 110 or 795) to find out exactly who built it, so I can source the right original factory part.
Should I Fix It Or Toss It?
My honest advice on the lifespan of your Dryer. Expand below.
Washers & Dryers
✓ Fix It: Clogged drain pumps, snapped dryer belts, burnt thermal fuses, or bad door latches. These are simple, fast, same-day fixes.
✕ Replace It: If a front-load washer sounds like a jet engine on spin cycle and it's over 8 years old, the rear tub bearing is shattered.
Typical repairs we handle in Vieux-Longueuil
Representative examples of what we find once the machine is open.
Dryer Fixed
Dispatched to Vieux-Longueuil. The Kenmore dryer was making a terrible squeaking noise. Opened it up and found the drum support rollers had flattened out. Rebuilt the roller assembly and replaced the belt.
Dryer Fixed
Got a call in Vieux-Longueuil. The Kenmore dryer wouldn't start at all, just clicked. Tested the door switch and found it was completely broken internally. Snapped in a new OEM door switch.