Cooking Fixed
The Saint-Laurentstove in Frigidaire locked its door mid-clean cycle and wouldn't open. Verified power, found the high-limit control board relay had shorted out. Put a new board in and recalibrated.
- 50+ Years Experience in Saint-Laurent
- Fully Insured
- 7 days, 6:30 AM–9:30 PM
Frigidaire Oven Repair in Saint-Laurent
Need Frigidaire oven repair in Saint-Laurent? $149.95 diagnostic applied to your repair, 7 days a week, 6:30 AM–9:30 PM. Call 514-700-0706.
Serving homeowners in and around Saint-Laurent: Hi, I'm Bob. I've been opening up washing machines and diagnosing fridges across Saint-Laurent for 50 years. I test it, find the exact broken part, and give you a straight path to fixing it.
$149.95 Diagnostic / Estimation Price: Applied directly to the cost of your repair.
Your local appliance technician in Saint-Laurent
“Cruising through the neighborhoods to fix a oven reminds me why I've done this for 50 years. From the busy main roads to your quiet driveway, I bring a fully stocked truck so you don't have to wait days for parts. I isolate the exact fault and fix it right the first time.”— Bob, Master Technician
Burnt Elements & Electrical Shorts
"When an oven in Saint-Laurent won't reach temperature, we check for blistered bake elements and arced terminal blocks to ensure 240V safety."
Frigidaire Oven problems I see in Saint-Laurent — and how I fix them
Select your oven issue below, and I'll tell you what I usually see when I open these up in Saint-Laurent.
Frigidaire Oven bake not heating — what usually causes it?
The lower 240V bake element cracked and burned out. I check the element for white blisters. If it's snapped, I unscrew it from the back wall and wire in a new one.
Failed Component: Bake Element
Frigidaire Oven uneven baking — what usually causes it?
The RTD temperature probe is drifting out of calibration as it gets hot. I pull the sensor from the back of the oven and test it. Replacing a bad probe stops it from burning your food.
Failed Component: Temp Sensor
Frigidaire Oven door stuck locked — what usually causes it?
The 900-degree self-clean cycle warped the metal locking mechanism. I have to manually trip the lock from the top or back, then replace the heat-damaged latch assembly.
Failed Component: Motorized Latch
Frigidaire Oven loud rattling — what usually causes it?
The bearings in the rear convection motor dried out from years of high heat. I pull the interior back panel off and replace the fan blade and motor assembly to make it whisper-quiet again.
Failed Component: Convection Fan
Frigidaire Oven display dead — what usually causes it?
The cooling fan failed, so the safety fuse popped to protect the control board. I trace the power. I replace the blown fuse on the back wall, but I also make sure the cooling fan is working.
Failed Component: Thermal Fuse
Frigidaire Oven preheats slowly — what usually causes it?
The board relay is burnt and dropping one leg of the 240V power, so it's running on 120V. I use an amp-clamp on the wires. If it's only pulling half power, I swap the weak element or the control board.
Failed Component: L2 Power Leg
Frigidaire Oven won't turn on — what usually causes it?
A loose connection at the wall cord melted the main power block. I check incoming voltage. If the block is charred, I cut back the damaged wires and splice in new ceramic nuts.
Failed Component: Terminal Block
Frigidaire Oven light won't turn on — what usually causes it?
The extreme oven heat oxidized the copper contacts inside the light socket. If a new bulb didn't fix it, I pull the housing out and splice in a brand-new ceramic socket assembly.
Failed Component: Halogen Socket
Frigidaire Oven self clean fails — what usually causes it?
The door switch is broken, so the board refuses to start the high-heat cycle for safety. I test the door plunger switch. If it's dead, replacing it allows the safety lockout to engage properly.
Failed Component: Door Interlock
Frigidaire Oven runs too hot — what usually causes it?
The heat relay on the main board is fused permanently closed. If you set it to 350 and it hits 600, it's getting unregulated power. I swap the entire Electronic Oven Control board.
Failed Component: EOC Relay
⚠️ Disclaimer: This is not DIY advice. Modern appliances utilize lethal high-voltage circuits. Diagnostics and repairs should only be performed by a Trained and Certified Appliance Service Technician.
$149.95 diagnostic, applied to your repair. Open 7 days, 6:30 AM–9:30 PM.
Common Frigidaire Oven error codes
| Code | What it means |
|---|---|
F10 | Runaway Temperature Detected |
F11 | Shorted Keypad / Stuck Button |
F30 | Open Oven Sensor Circuit |
The Right Parts Make the Repair
We don't mess around with cheap aftermarket knock-offs. If we fix your Frigidaire oven, we use genuine OEM parts. They fit right, and they last.
| OEM SKU | Component description |
|---|---|
316075103 | Frigidaire Bake Element |
I Know These Brands Inside and Out
After many years, you learn the quirks of every manufacturer. I stock the truck based on what breaks the most.
Frigidaire & Electrolux
If your Frigidaire fridge starts beeping with a "SY EF" code, the freezer fan died. For their front-load washers, if the door won't unlock, the latch wax motor burned out. I bypass the lock, get your laundry out, and swap the latch assembly.
Should I Fix It Or Toss It?
My honest advice on the lifespan of your Oven. Expand below.
Ovens & Stoves
✓ Fix It: Stoves last forever. Always replace burnt bake elements, bad surface switches, or ignitors. It's an easy fix.
✕ Replace It: Only if a massive power surge fries a discontinued main logic board on a unit that is over 15 years old.
Typical repairs we handle in Saint-Laurent
Representative examples of what we find once the machine is open.
Cooking Fixed
Dispatched to Saint-Laurent. The Frigidaire oven was taking 45 minutes to preheat. Amp-clamped the bottom bake element and found it was only pulling 120V. Replaced the blistered element.
Cooking Fixed
Got a call in Saint-Laurent. A radiant burner on the Frigidaire cooktop wouldn't turn off, just stayed blazing hot. Pulled the back panel and swapped the fused infinite surface switch. Safety hazard resolved.