Washer Fixed
Dispatched to Saint-Hubert. The Samsung washing machine stopped mid-cycle and wouldn't drain. Cleared a baby sock out of the drain pump trap. Tested the motor, runs perfect.
- 50+ Years Experience in Saint-Hubert
- Fully Insured
- 7 days, 6:30 AM–9:30 PM
Samsung Washer Repair in Saint-Hubert
Need Samsung washer repair in Saint-Hubert? $149.95 diagnostic applied to your repair, 7 days a week, 6:30 AM–9:30 PM. Call 514-700-0706.
Serving homeowners in and around Saint-Hubert: Hi, I'm Bob. I've been opening up washing machines and diagnosing fridges across Saint-Hubert for 50 years. I test it, find the exact broken part, and give you a straight path to fixing it.
$149.95 Diagnostic / Estimation Price: Applied directly to the cost of your repair.
Your local appliance technician in Saint-Hubert
“Cruising through the neighborhoods to fix a washer reminds me why I've done this for 50 years. From the busy main roads to your quiet driveway, I bring a fully stocked truck so you don't have to wait days for parts. I isolate the exact fault and fix it right the first time.”— Bob, Master Technician
Heavy Loads & Drain Clogs
"Most service calls in Saint-Hubert for washers full of water aren't dead motors; they are pump blockages. We clear the impeller and test the drain cycle immediately."
What's Actually Wrong With It?
Samsung Washer problems I see in Saint-Hubert — and how I fix them
Select your washer issue below, and I'll tell you what I usually see when I open these up in Saint-Hubert.
Samsung Washer won't drain — what usually causes it?
Coins or bobby pins jammed the drain pump impeller. I open the lower panel, physically clear the clog from the trap, and test the motor to make sure it didn't burn out.
Failed Component: Drain Pump
Samsung Washer clothes wet — what usually causes it?
A bad Hall sensor (Rotor Position) or a snapped drive belt is preventing high RPMs. I test the speed sensor communication. If it's dead, the board aborts the spin. I replace the sensor or belt.
Failed Component: Spin Cycle
Samsung Washer leaking door — what usually causes it?
A rip in the massive rubber gasket, usually from catching a zipper in the door. I pull the front chassis off, remove the tension springs, and seat a brand-new factory rubber bellows.
Failed Component: Door Bellows
Samsung Washer shaking violently — what usually causes it?
The hydraulic shock absorbers or suspension rods have lost their dampening fluid. I press down on the tub. If it bounces like a basketball, the shocks are shot. I replace the full set of four.
Failed Component: Suspension System
Samsung Washer won't agitate — what usually causes it?
Shattered motor coupling or stripped nylon agitator dogs. I tip the machine back and check the linkage. It's usually a quick fix replacing the plastic drive components.
Failed Component: Transmission / Coupling
Samsung Washer fills slowly — what usually causes it?
Hard water calcium has completely blocked the mesh screens, or the solenoids are weak. I check the hoses first. If they are clear, I ohm-test the 120V water valve and replace it if the coils are failing.
Failed Component: Inlet Valve
Samsung Washer completely dead — what usually causes it?
A broken door switch interlock. The machine won't start if it thinks the door is open. I trace the power from the wall plug to the board. Usually, I just need to swap the broken door latch assembly.
Failed Component: Power Supply
Samsung Washer stops mid cycle — what usually causes it?
The water level sensor is getting bad data from a clogged air dome tube. I blow out the pressure hose. If the sensor is still reading wrong, I replace the analog switch on the console.
Failed Component: Pressure Switch
Samsung Washer door stuck — what usually causes it?
The wax motor in the lock burned out, or there's still water in the tub. I use the manual bypass to get your laundry out, then diagnose whether the pump or the lock itself failed.
Failed Component: Door Latch Solenoid
Samsung Washer mold smell — what usually causes it?
Soap scum and bacteria buildup behind the drum from using too much cold water. I run a deep chemical descaling and physically clean the door boot where the bio-film hides.
Failed Component: Outer Tub Bearing
⚠️ Disclaimer: This is not DIY advice. Modern appliances utilize lethal high-voltage circuits. Diagnostics and repairs should only be performed by a Trained and Certified Appliance Service Technician.
$149.95 diagnostic, applied to your repair. Open 7 days, 6:30 AM–9:30 PM.
Common Samsung Washer error codes
| Code | What it means |
|---|---|
5C | Drain Filter/Pump Clogged |
4C | Water Supply Timeout |
3E | Stator Motor Defect |
The Right Parts Make the Repair
We don't mess around with cheap aftermarket knock-offs. If we fix your Samsung washer, we use genuine OEM parts. They fit right, and they last.
| OEM SKU | Component description |
|---|---|
DC97-16984A | Samsung Drain Pump |
I Know These Brands Inside and Out
After many years, you learn the quirks of every manufacturer. I stock the truck based on what breaks the most.
Samsung & LG
Korean brands use a lot of smart electronics. For LG, if it won't spin, it's usually the Hall Sensor on the direct-drive motor. For Samsung fridges, if the ice maker freezes over, I have to install a redesigned OEM heater clip to stop it from happening again. I stock these specific parts in the truck.
Should I Fix It Or Toss It?
My honest advice on the lifespan of your Washer. Expand below.
Washers & Dryers
✓ Fix It: Clogged drain pumps, snapped dryer belts, burnt thermal fuses, or bad door latches. These are simple, fast, same-day fixes.
✕ Replace It: If a front-load washer sounds like a jet engine on spin cycle and it's over 8 years old, the rear tub bearing is shattered.
Typical repairs we handle in Saint-Hubert
Representative examples of what we find once the machine is open.
Washer Fixed
Arrived in Saint-Hubert. The Samsung washer was shaking violently on spin cycle. The hydraulic suspension rods had lost all their dampening fluid. Replaced the set of 4 rods.
Washer Fixed
Customer in Saint-Hubert said their Samsung washer door wouldn't unlock. Found a burnt-out wax motor in the latch assembly. Bypassed the lock to get their laundry out, installed new latch.