Washer Fixed
Arrived in Mercier. The Frigidaire washer was shaking violently on spin cycle. The hydraulic suspension rods had lost all their dampening fluid. Replaced the set of 4 rods.
- 50+ Years Experience in Mercier
- Fully Insured
- 7 days, 6:30 AM–9:30 PM
Frigidaire Washer Repair in Mercier
Need Frigidaire washer repair in Mercier? $149.95 diagnostic applied to your repair, 7 days a week, 6:30 AM–9:30 PM. Call 514-700-0706.
Serving homeowners in and around Mercier: Hi, I'm Bob. I've been opening up washing machines and diagnosing fridges across Mercier for 50 years. I test it, find the exact broken part, and give you a straight path to fixing it.
$149.95 Diagnostic / Estimation Price: Applied directly to the cost of your repair.
Your local appliance technician in Mercier
“Cruising through the neighborhoods to fix a washer reminds me why I've done this for 50 years. From the busy main roads to your quiet driveway, I bring a fully stocked truck so you don't have to wait days for parts. I isolate the exact fault and fix it right the first time.”— Bob, Master Technician
Heavy Loads & Drain Clogs
"Most service calls in Mercier for washers full of water aren't dead motors; they are pump blockages. We clear the impeller and test the drain cycle immediately."
What's Actually Wrong With It?
Frigidaire Washer problems I see in Mercier — and how I fix them
Select your washer issue below, and I'll tell you what I usually see when I open these up in Mercier.
Frigidaire Washer won't drain — what usually causes it?
Coins or bobby pins jammed the drain pump impeller. I open the lower panel, physically clear the clog from the trap, and test the motor to make sure it didn't burn out.
Failed Component: Drain Pump
Frigidaire Washer clothes wet — what usually causes it?
A bad Hall sensor (Rotor Position) or a snapped drive belt is preventing high RPMs. I test the speed sensor communication. If it's dead, the board aborts the spin. I replace the sensor or belt.
Failed Component: Spin Cycle
Frigidaire Washer leaking door — what usually causes it?
A rip in the massive rubber gasket, usually from catching a zipper in the door. I pull the front chassis off, remove the tension springs, and seat a brand-new factory rubber bellows.
Failed Component: Door Bellows
Frigidaire Washer shaking violently — what usually causes it?
The hydraulic shock absorbers or suspension rods have lost their dampening fluid. I press down on the tub. If it bounces like a basketball, the shocks are shot. I replace the full set of four.
Failed Component: Suspension System
Frigidaire Washer won't agitate — what usually causes it?
Shattered motor coupling or stripped nylon agitator dogs. I tip the machine back and check the linkage. It's usually a quick fix replacing the plastic drive components.
Failed Component: Transmission / Coupling
Frigidaire Washer fills slowly — what usually causes it?
Hard water calcium has completely blocked the mesh screens, or the solenoids are weak. I check the hoses first. If they are clear, I ohm-test the 120V water valve and replace it if the coils are failing.
Failed Component: Inlet Valve
Frigidaire Washer completely dead — what usually causes it?
A broken door switch interlock. The machine won't start if it thinks the door is open. I trace the power from the wall plug to the board. Usually, I just need to swap the broken door latch assembly.
Failed Component: Power Supply
Frigidaire Washer stops mid cycle — what usually causes it?
The water level sensor is getting bad data from a clogged air dome tube. I blow out the pressure hose. If the sensor is still reading wrong, I replace the analog switch on the console.
Failed Component: Pressure Switch
Frigidaire Washer door stuck — what usually causes it?
The wax motor in the lock burned out, or there's still water in the tub. I use the manual bypass to get your laundry out, then diagnose whether the pump or the lock itself failed.
Failed Component: Door Latch Solenoid
Frigidaire Washer mold smell — what usually causes it?
Soap scum and bacteria buildup behind the drum from using too much cold water. I run a deep chemical descaling and physically clean the door boot where the bio-film hides.
Failed Component: Outer Tub Bearing
⚠️ Disclaimer: This is not DIY advice. Modern appliances utilize lethal high-voltage circuits. Diagnostics and repairs should only be performed by a Trained and Certified Appliance Service Technician.
$149.95 diagnostic, applied to your repair. Open 7 days, 6:30 AM–9:30 PM.
Common Frigidaire Washer error codes
| Code | What it means |
|---|---|
E11 | Fill Time Too Long |
E21 | Water Not Draining Fast Enough |
E41 | Door Open During Cycle |
The Right Parts Make the Repair
We don't mess around with cheap aftermarket knock-offs. If we fix your Frigidaire washer, we use genuine OEM parts. They fit right, and they last.
| OEM SKU | Component description |
|---|---|
137108100 | Frigidaire Pump |
I Know These Brands Inside and Out
After many years, you learn the quirks of every manufacturer. I stock the truck based on what breaks the most.
Frigidaire & Electrolux
If your Frigidaire fridge starts beeping with a "SY EF" code, the freezer fan died. For their front-load washers, if the door won't unlock, the latch wax motor burned out. I bypass the lock, get your laundry out, and swap the latch assembly.
Should I Fix It Or Toss It?
My honest advice on the lifespan of your Washer. Expand below.
Washers & Dryers
✓ Fix It: Clogged drain pumps, snapped dryer belts, burnt thermal fuses, or bad door latches. These are simple, fast, same-day fixes.
✕ Replace It: If a front-load washer sounds like a jet engine on spin cycle and it's over 8 years old, the rear tub bearing is shattered.
Typical repairs we handle in Mercier
Representative examples of what we find once the machine is open.
Washer Fixed
Customer in Mercier said their Frigidaire washer door wouldn't unlock. Found a burnt-out wax motor in the latch assembly. Bypassed the lock to get their laundry out, installed new latch.
Washer Fixed
Got a call for a leaking Frigidaire washer in Mercier. Found a tear in the rubber door boot from an overloaded spin cycle. Pulled the front panel, put a new OEM gasket on. No more leaks.