Washer Fixed
Customer in Longueuil said their Inglis washer door wouldn't unlock. Found a burnt-out wax motor in the latch assembly. Bypassed the lock to get their laundry out, installed new latch.
- 50+ Years Experience in Longueuil
- Fully Insured
- 7 days, 6:30 AM–9:30 PM
Inglis Washer Repair in Longueuil
Need Inglis washer repair in Longueuil? $149.95 diagnostic applied to your repair, 7 days a week, 6:30 AM–9:30 PM. Call 514-700-0706.
Serving homeowners in and around Longueuil: Hi, I'm Bob. I've been opening up washing machines and diagnosing fridges across Longueuil for 50 years. I test it, find the exact broken part, and give you a straight path to fixing it.
$149.95 Diagnostic / Estimation Price: Applied directly to the cost of your repair.
Your local appliance technician in Longueuil
“Crossing the Jacques Cartier Bridge into Longueuil always reminds me of the deep roots in this area. The homes are established, and the families here want appliances that last. I combine 50 years of mechanical knowledge with the latest diagnostic tools to repair your washer efficiently.”— Bob, Master Technician
Heavy Loads & Drain Clogs
"Most service calls in Longueuil for washers full of water aren't dead motors; they are pump blockages. We clear the impeller and test the drain cycle immediately."
What's Actually Wrong With It?
Inglis Washer problems I see in Longueuil — and how I fix them
Select your washer issue below, and I'll tell you what I usually see when I open these up in Longueuil.
Inglis Washer won't drain — what usually causes it?
Coins or bobby pins jammed the drain pump impeller. I open the lower panel, physically clear the clog from the trap, and test the motor to make sure it didn't burn out.
Failed Component: Drain Pump
Inglis Washer clothes wet — what usually causes it?
A bad Hall sensor (Rotor Position) or a snapped drive belt is preventing high RPMs. I test the speed sensor communication. If it's dead, the board aborts the spin. I replace the sensor or belt.
Failed Component: Spin Cycle
Inglis Washer leaking door — what usually causes it?
A rip in the massive rubber gasket, usually from catching a zipper in the door. I pull the front chassis off, remove the tension springs, and seat a brand-new factory rubber bellows.
Failed Component: Door Bellows
Inglis Washer shaking violently — what usually causes it?
The hydraulic shock absorbers or suspension rods have lost their dampening fluid. I press down on the tub. If it bounces like a basketball, the shocks are shot. I replace the full set of four.
Failed Component: Suspension System
Inglis Washer won't agitate — what usually causes it?
Shattered motor coupling or stripped nylon agitator dogs. I tip the machine back and check the linkage. It's usually a quick fix replacing the plastic drive components.
Failed Component: Transmission / Coupling
Inglis Washer fills slowly — what usually causes it?
Hard water calcium has completely blocked the mesh screens, or the solenoids are weak. I check the hoses first. If they are clear, I ohm-test the 120V water valve and replace it if the coils are failing.
Failed Component: Inlet Valve
Inglis Washer completely dead — what usually causes it?
A broken door switch interlock. The machine won't start if it thinks the door is open. I trace the power from the wall plug to the board. Usually, I just need to swap the broken door latch assembly.
Failed Component: Power Supply
Inglis Washer stops mid cycle — what usually causes it?
The water level sensor is getting bad data from a clogged air dome tube. I blow out the pressure hose. If the sensor is still reading wrong, I replace the analog switch on the console.
Failed Component: Pressure Switch
Inglis Washer door stuck — what usually causes it?
The wax motor in the lock burned out, or there's still water in the tub. I use the manual bypass to get your laundry out, then diagnose whether the pump or the lock itself failed.
Failed Component: Door Latch Solenoid
Inglis Washer mold smell — what usually causes it?
Soap scum and bacteria buildup behind the drum from using too much cold water. I run a deep chemical descaling and physically clean the door boot where the bio-film hides.
Failed Component: Outer Tub Bearing
⚠️ Disclaimer: This is not DIY advice. Modern appliances utilize lethal high-voltage circuits. Diagnostics and repairs should only be performed by a Trained and Certified Appliance Service Technician.
$149.95 diagnostic, applied to your repair. Open 7 days, 6:30 AM–9:30 PM.
Common Inglis Washer error codes
| Code | What it means |
|---|---|
F21 | Drain Pump Impeller Blocked |
F22 | Door Lock Actuator Failed |
F51 | Motor Rotor Position Sensor Fault |
Should I Fix It Or Toss It?
My honest advice on the lifespan of your Washer. Expand below.
Washers & Dryers
✓ Fix It: Clogged drain pumps, snapped dryer belts, burnt thermal fuses, or bad door latches. These are simple, fast, same-day fixes.
✕ Replace It: If a front-load washer sounds like a jet engine on spin cycle and it's over 8 years old, the rear tub bearing is shattered.
Typical repairs we handle in Longueuil
Representative examples of what we find once the machine is open.
Washer Fixed
Got a call for a leaking Inglis washer in Longueuil. Found a tear in the rubber door boot from an overloaded spin cycle. Pulled the front panel, put a new OEM gasket on. No more leaks.
Washer Fixed
Dispatched to Longueuil. The Inglis washing machine stopped mid-cycle and wouldn't drain. Cleared a baby sock out of the drain pump trap. Tested the motor, runs perfect.