Cooking Fixed
Got a call in Longueuil. A radiant burner on the Frigidaire cooktop wouldn't turn off, just stayed blazing hot. Pulled the back panel and swapped the fused infinite surface switch. Safety hazard resolved.
- 50+ Years Experience in Longueuil
- Fully Insured
- 7 days, 6:30 AM–9:30 PM
Frigidaire Wall Oven Repair in Longueuil
Need Frigidaire wall oven repair in Longueuil? $149.95 diagnostic applied to your repair, 7 days a week, 6:30 AM–9:30 PM. Call 514-700-0706.
Serving homeowners in and around Longueuil: Hi, I'm Bob. I've been opening up washing machines and diagnosing fridges across Longueuil for 50 years. I test it, find the exact broken part, and give you a straight path to fixing it.
$149.95 Diagnostic / Estimation Price: Applied directly to the cost of your repair.
Your local appliance technician in Longueuil
“Crossing the Jacques Cartier Bridge into Longueuil always reminds me of the deep roots in this area. The homes are established, and the families here want appliances that last. I combine 50 years of mechanical knowledge with the latest diagnostic tools to repair your wall oven efficiently.”— Bob, Master Technician
Burnt Elements & Electrical Shorts
"When an oven in Longueuil won't reach temperature, we check for blistered bake elements and arced terminal blocks to ensure 240V safety."
Frigidaire Wall Oven problems I see in Longueuil — and how I fix them
Select your wall oven issue below, and I'll tell you what I usually see when I open these up in Longueuil.
Frigidaire Wall Oven bake not heating — what usually causes it?
The lower 240V bake element cracked and burned out. I check the element for white blisters. If it's snapped, I unscrew it from the back wall and wire in a new one.
Failed Component: Bake Element
Frigidaire Wall Oven uneven baking — what usually causes it?
The RTD temperature probe is drifting out of calibration as it gets hot. I pull the sensor from the back of the oven and test it. Replacing a bad probe stops it from burning your food.
Failed Component: Temp Sensor
Frigidaire Wall Oven door stuck locked — what usually causes it?
The 900-degree self-clean cycle warped the metal locking mechanism. I have to manually trip the lock from the top or back, then replace the heat-damaged latch assembly.
Failed Component: Motorized Latch
Frigidaire Wall Oven loud rattling — what usually causes it?
The bearings in the rear convection motor dried out from years of high heat. I pull the interior back panel off and replace the fan blade and motor assembly to make it whisper-quiet again.
Failed Component: Convection Fan
Frigidaire Wall Oven display dead — what usually causes it?
The cooling fan failed, so the safety fuse popped to protect the control board. I trace the power. I replace the blown fuse on the back wall, but I also make sure the cooling fan is working.
Failed Component: Thermal Fuse
Frigidaire Wall Oven preheats slowly — what usually causes it?
The board relay is burnt and dropping one leg of the 240V power, so it's running on 120V. I use an amp-clamp on the wires. If it's only pulling half power, I swap the weak element or the control board.
Failed Component: L2 Power Leg
Frigidaire Wall Oven won't turn on — what usually causes it?
A loose connection at the wall cord melted the main power block. I check incoming voltage. If the block is charred, I cut back the damaged wires and splice in new ceramic nuts.
Failed Component: Terminal Block
Frigidaire Wall Oven light won't turn on — what usually causes it?
The extreme oven heat oxidized the copper contacts inside the light socket. If a new bulb didn't fix it, I pull the housing out and splice in a brand-new ceramic socket assembly.
Failed Component: Halogen Socket
Frigidaire Wall Oven self clean fails — what usually causes it?
The door switch is broken, so the board refuses to start the high-heat cycle for safety. I test the door plunger switch. If it's dead, replacing it allows the safety lockout to engage properly.
Failed Component: Door Interlock
Frigidaire Wall Oven runs too hot — what usually causes it?
The heat relay on the main board is fused permanently closed. If you set it to 350 and it hits 600, it's getting unregulated power. I swap the entire Electronic Oven Control board.
Failed Component: EOC Relay
⚠️ Disclaimer: This is not DIY advice. Modern appliances utilize lethal high-voltage circuits. Diagnostics and repairs should only be performed by a Trained and Certified Appliance Service Technician.
$149.95 diagnostic, applied to your repair. Open 7 days, 6:30 AM–9:30 PM.
Common Frigidaire Wall Oven error codes
| Code | What it means |
|---|---|
F10 | Runaway Temperature Detected |
F11 | Shorted Keypad / Stuck Button |
F30 | Open Oven Sensor Circuit |
The Right Parts Make the Repair
We don't mess around with cheap aftermarket knock-offs. If we fix your Frigidaire wall oven, we use genuine OEM parts. They fit right, and they last.
| OEM SKU | Component description |
|---|---|
316075103 | Frigidaire Bake Element |
I Know These Brands Inside and Out
After many years, you learn the quirks of every manufacturer. I stock the truck based on what breaks the most.
Frigidaire & Electrolux
If your Frigidaire fridge starts beeping with a "SY EF" code, the freezer fan died. For their front-load washers, if the door won't unlock, the latch wax motor burned out. I bypass the lock, get your laundry out, and swap the latch assembly.
Should I Fix It Or Toss It?
My honest advice on the lifespan of your Wall Oven. Expand below.
Ovens & Stoves
✓ Fix It: Stoves last forever. Always replace burnt bake elements, bad surface switches, or ignitors. It's an easy fix.
✕ Replace It: Only if a massive power surge fries a discontinued main logic board on a unit that is over 15 years old.
Typical repairs we handle in Longueuil
Representative examples of what we find once the machine is open.
Cooking Fixed
Arrived in Longueuil. Client's Frigidaire stove touchpad was completely unresponsive. Found steam had gotten behind the glass and shorted the ribbon cable. Installed a new UI membrane.
Cooking Fixed
The Longueuilstove in Frigidaire locked its door mid-clean cycle and wouldn't open. Verified power, found the high-limit control board relay had shorted out. Put a new board in and recalibrated.